Compatible bows are the. The bows IBO speed ratings are 330 fps at 65 percent letoff 325 fps at 75 percent.
Mathews No Cam Htr
See below for an instructional video and an adjustment chart to.
. Shouldnt be more than 30. One rotation of the bolt increases or decreases the draw weight by about two to four pounds. They just swapped out the limbs to make it a 60-70.
With the exception of the Mathews Mission series Mathews bows are designed draw length specific and do not provide for setting adjustment. When I had increased the draw to about 40 and decided to start going to my local 3D shoots again I reduced the draw weight on one of my Mathews from 70 to 40 and sighted it in. VXR 28 315 Weights.
24 to 30 inches in half-inch increments. He aint wrong hes just different and his pride wont let him do things to make you think hes right. As noted earlier these modules can change both your draw length as well as your let-off which will change your bows speed.
Remove the setscrews in the cams with a screwdriver. Insert the Allen wrench into one of the limb bolts on the bow. Same size cam as on all my other Mathews bows but this sucker is proving harder to tune.
Brace Height6 58 inches. As for the 50-60 or 60-70 models my bow was a 50-60 on the floor. In this video we will go over the new Mathews bow that I got awhile back.
So I went to my local archery. Mathews Chill Draw Length Question Archery Talk Forum Most Mathews bows are engineered to be draw length specific and offer no draw length adjustment on the cam. Each mod is programmed to deliver maximum efficiency resulting in an ultra-smooth draw without sacrificing speed.
Repeat steps one and two on the other limb bolt. Mathews No Cam HTR Specs. The rating of this product is.
The limb bolt should be snug. Mathews Vertix Draw Length Adjustment. Simply remove the two allen screws that hold the module to the wheel and install your new module in its place.
While the Mission series draw length can be changed with a setscrew on the cams you will need to replace the cams to change the draw length on other models of Mathews bows. Modules are labeled A through J See charts for appropriate draw length selection. Turn the limb bolt clockwise to increase the draw weight or counterclockwise to decrease the draw weight.
We take the new Mathews No Cam HTR for a test run. Other Mathews cams are adjustable for. V3X 29.
How do you change the draw length on a Mathews no cam. Take it to a Mathews dealer and theyll order you the correct mods. There are several slots in a row on the bottom cam and the string is moved to the appropriate slot only after the bow has been safely compressed on a bow press of courseto adjust draw length.
Letoff 65 75 85 optional. Draw length can be changed by changing the mods. Its only a couple Allen screws to take out.
Adjusting the draw length on your Mission bow has never been easier than with new FastFit Cam Technology. Or if you know what draw length you are you can try and find a set on archery talk. The lower the let-off the faster the bow.
As noted earlier these modules can change both your draw length as well as. Modules to suit the Mathews HTR and TRG No-Cam bows. Its available in peak draw weights of 50 60 or 70 pounds and has an adjustable system letoff of 65 75 or 85 percent.
Loosen slide and retighten. Zero problems with either bow both shot smoothly and with little adjustment needed except the vertical adjustment of the sight pins to compensate for the slower. FastFit Cam technology is utilized on the Hammr Radik and Switch.
Draw weight adjustments are made using either a 316 or 732 Allen Wrench. If my draw length is off by a hair it drives me nuts. The NO CAM HTR weighs 43 pounds has a 6 58-inch brace height and can accommodate draw lengths from 24-30 inches in half-inch increments.
Your shooting style should be measured to ensure a proper fit. Draw Length If your new Mathews SoloCam bow is equipped with a StraightLine MaxCam which is draw length specific there is no adjustment on the cam. I think that a Matthews dealer can order a new cam for you and change the draw length.
Turn the limb bolt clockwise to increase the draw weight and counter clockwise to decrease the weight. Mathews module for Mathews model bows for modular draw length adjustment. Most Mathews bows are engineered to be draw length specific and offer no draw length adjustment on the cam.
Both limb bolts must be adjusted equally or the bow may become out of tunesynchronization. This bow had a draw length that was to long for me. Draw lengths can be changed in under 30 seconds with the simple use of an allen wrench.
Them that dont know him wont like him and them that do sometimes wont know how to take him. See image for module chart. Simply remove the two allen screws that hold the module to the wheel and install your new module in its place.
41443 pounds approximate Axle-To-Axle Length. How do you change the draw length on a Mathews no Cam. Was shooting at my coachs last night and he and another shooter there both Mathews sponsored shooters said that theyve noticed on the Z7 and the Triumph that the draw length was longer than usual.
Mathews bows with SwitchWeight technology allows for adjustment of Draw Length Draw Weight and Let-Off all with the swapping of a cam module. Sent from my iPhone using Tapatalk. Adjust peak draw weight and draw length with the quick change of a module.
High-efficiency CAM system that delivers accurate energy with an incredibly smooth draw.
No Cam Htr Draw Length And Draw Weight Off Archery Talk Forum
Mathews Nocam Htr Review Western Whitetail Presented By Drcmedia
Mathews No Cam Modules Urban Archery Pty Ltd
No Cam Htr Timing Archery Talk Forum
2009 2010 Mathews Owners Manual By Mathews Inc Issuu
Mathews Archery Inc Introducing Switchweight Technology No More Messing With Your Limbs Simply Adjust The Peak Weight Of Your Bow With The Quick Change Of A Mod Each Module Is
Cam Adjustment Mission Archery By Mathews
Mathews Htr No Cam Review Bowhunting Com
0 comments
Post a Comment